[HTML][HTML] The peach RGF/GLV signaling peptide pCTG134 is involved in a regulatory circuit that sustains auxin and ethylene actions
…, U Salvagnin, F Resentini, S Quaresimin… - Frontiers in Plant …, 2017 - frontiersin.org
… States), according to the manufacturer’s instructions and confirmed by sequencing. The …
-fluorometer according to the manufacturer’s instructions. The GUS activity was expressed …
-fluorometer according to the manufacturer’s instructions. The GUS activity was expressed …
[HTML][HTML] Effect of voids on the crack formation in a [45/− 45/0] s laminate under cyclic axial tension
L Maragoni, PA Carraro, M Quaresimin - Composites Part A: Applied …, 2016 - Elsevier
In the present work, the influence of manufacturing induced voids on damage mechanisms
at the microscopic scale was analysed on [45/−45/0] s laminates subjected to tension fatigue …
at the microscopic scale was analysed on [45/−45/0] s laminates subjected to tension fatigue …
Low‐to high‐velocity frictional properties of the clay‐rich gouges from the slipping zone of the 1963 Vaiont slide, northern Italy
…, H Noda, T Shimamoto, M Quaresimin… - Journal of …, 2011 - Wiley Online Library
… v < 5.0 × 10 −5 m/s to 0.12 at 1.31 m/s. Microstructural and mineralogical analyses of the
gouge … at v < 1.0 × 10 −4 m/s to 0.0 at v > 0.70 m/s: full lubrication results from the formation of a …
gouge … at v < 1.0 × 10 −4 m/s to 0.0 at v > 0.70 m/s: full lubrication results from the formation of a …
Fatigue behaviour of glass/epoxy laminates in the presence of voids
…, PA Carraro, M Peron, M Quaresimin - International journal of …, 2017 - Elsevier
… In the present work, glass/epoxy panels with stacking sequence [0/90 2 ] S and [0/45 2 /0/−45
2 ] S were produced by vacuum resin infusion. Using different process parameters, which …
2 ] S were produced by vacuum resin infusion. Using different process parameters, which …
[HTML][HTML] Damage evolution under cyclic multiaxial stress state: A comparative analysis between glass/epoxy laminates and tubes
M Quaresimin, PA Carraro, LP Mikkelsen… - Composites Part B …, 2014 - Elsevier
… The stacking sequence [0/θ 2 /0/−θ 2 ] s has been adopted in order to investigate the influence
of … Results are presented in terms of S–N curves for the initiation of the first cracks, crack …
of … Results are presented in terms of S–N curves for the initiation of the first cracks, crack …
Cumulative damage of short glass fiber reinforced thermoplastics
…, GS Springer, M Quaresimin - Journal of reinforced …, 2001 - journals.sagepub.com
Tests were conducted measuring the fatigue lives of 150 mm by 10 mm by 2 mm short glass
fiber reinforced Copolyamide coupons under different types of cyclic loads. The fatigue lives …
fiber reinforced Copolyamide coupons under different types of cyclic loads. The fatigue lives …
Two‐stage fatigue loading of woven carbon fibre reinforced laminates
MS Found, M Quaresimin - Fatigue & Fracture of Engineering …, 2003 - Wiley Online Library
A brief review of the models used to predict the cumulative fatigue damage in FRP composites
is presented. Two‐stage fatigue loading of a [0/90,± 45 2 ,0/90] s quasi‐ isotropic woven …
is presented. Two‐stage fatigue loading of a [0/90,± 45 2 ,0/90] s quasi‐ isotropic woven …
Characterisation and analysis of transverse crack-induced delamination in cross-ply composite laminates under fatigue loadings
PA Carraro, L Maragoni, M Quaresimin - International Journal of Fatigue, 2019 - Elsevier
… In this work, glass/epoxy cross-ply laminates with lay-up [0 2 /90 4 ] s and [0/90 2 ] s were
produced by vacuum infusion and tested under tension-tension cyclic loadings. During the tests…
produced by vacuum infusion and tested under tension-tension cyclic loadings. During the tests…
Influence of manufacturing induced defects on damage initiation and propagation in carbon/epoxy NCF laminates
…, L Maragoni, M Quaresimin - … Manufacturing: Polymer & …, 2015 - Taylor & Francis
In the present work, two sets of NCF carbon/epoxy laminates have been produced via liquid
infusion molding, with the aim to investigate the influence of some process parameters on …
infusion molding, with the aim to investigate the influence of some process parameters on …
Damage initiation and evolution in glass/epoxy tubes subjected to combined tension–torsion fatigue loading
M Quaresimin, PA Carraro - International Journal of Fatigue, 2014 - Elsevier
… Attention was focused on the initiation and propagation of cracks in the 90 layers, and
fatigue data are presented in terms of S–N curves (for crack initiation) and Paris-like curves (for …
fatigue data are presented in terms of S–N curves (for crack initiation) and Paris-like curves (for …